After Hours - HRW DG, Licence to Perform Dogging - CPCCLDG3001

This Nationally Recognised CPCCLDG3001 Licence to Perform Dogging (DG) course is designed to provide participants with the essential knowledge & skills required for slinging techniques and the selection and inspection of lifting gear as well as directing the crane operator and determining safe ways of supporting different loads.

On completion of the training, participants will be ready to undertake the SafeWork NSW assessment required to receive their High-Risk Work Licence to Perform Dogging.

 

 COURSE TOPICS 

• Workplace Health & Safety Legislation & operating procedures
• Hazard identification, Assess risks & control measures
• Plan work
• Overhead hazards
• Damage and defect reporting
• Communication methods
• Whistle & hand signals
• Select & inspect lifting equipment
• Determining load weight & SWL
• Attach & secure the load
• Shift load, including directing and maneuvering the load to different locations
• Unplanned & or unsafe situations
• Inspect and separate defective equipment
• Reporting procedures
• Shutdown & secure site

 

Prerequisites & High-Risk Work Licence (HRW) Assessment Requirements

To enrol in this course, candidates must meet the following requirements:

• Be at least 18 years of age
• Hold a Unique Student Identifier (USI)
  If you do not have a USI, you can create one at: https://www.usi.gov.au/
• Have a Service NSW account
  This account is required to verify your identity and to enrol in your High-Risk Work Licence (HRWL) assessment.
• Provide one approved form of photo identification on the day of assessment for identity verification by the Assessor.
• Demonstrate basic English language and numeracy skills
  Candidates must be able to read, write, and communicate in English at a level that ensures they can safely perform high-risk work and follow instructions during training and assessment.

 

Language, Literacy, Numeracy & Digital (LLND) Requirements

• As part of the enrolment process, you will be required to complete a short pre-enrolment LLND quiz.
• This quiz takes approximately 10 minutes and helps us ensure you receive the right level of support during your training.
• A link to the quiz will be provided when you apply to enrol in the course.
• If you believe you may experience any literacy, numeracy, or learning difficulties, please let us know during enrolment. We are committed to supporting all candidates and can arrange appropriate training and assessment assistance where needed.
• We also offer one-on-one training and assessment for approved candidates. If you are interested in this option, please contact our admin team before enrolling to discuss eligibility and availability.

 

Course Duration

• Training: 2 weeks (37 hours total)
  Face-to-face practical and theory training delivered over three evening sessions per week.
• Knowledge Assessment:
  A 2-hour written test
• Practical (Performance) Assessment:
  2- hour per candidate
• SafeWork NSW HRW Licence Assessment: 1 Day - (this session is run during the day on the weekend) 

 

Candidate Requirements

• Candidates must present one approved form of photo identification on the day of assessment for identity verification by the Assessor.
• Candidates may leave the facility during their scheduled break if they wish. Complimentary water, tea, coffee, and biscuits will be provided. 
• Appropriate Personal Protective Equipment (PPE) is required for all practical training and SafeWork NSW assessment activities. Hard hats, high visibility vests, gloves, and whistles are provided if you do not have your own.
• At a minimum, footwear must be fully enclosed and suitable for construction or industrial worksites.  Suitable footwear includes: Steel-capped or safety boots, Boots with slip-resistant soles, Footwear that provides good support and protection.

Important

• There have been some recent changes to how candidates prepare for and obtain their SafeWork High-Risk Work (HRW) Licence.

• To make sure you’re fully prepared, please read the course instructions carefully. These will be sent to your email once your registration is confirmed. Following them closely will help ensure a smooth training and assessment experience.

 

Assessment Process

• This course is delivered in accordance with the national standards for licencing persons performing high-risk work. Training combines theoretical knowledge, calculations, and practical skills, allowing candidates to demonstrate the industry competencies outlined in the relevant units of competency.
• Upon completion of the training, candidates will undertake an RTO assessment. This assessment evaluates readiness for the SafeWork NSW High-Risk Work (HRW) assessment and identifies any areas where further training may be required.
• To successfully pass the SafeWork NSW assessment, candidates must correctly demonstrate all critical components of the tasks and answer associated questions accurately.

 

Course Outcome

Upon successful completion of the SafeWork NSW assessment, candidates will receive:

• A Nationally Recognised Statement of Attainment for CPCCLDG3001 Licence to Perform Dogging (DG).
• This qualification is recognised within the Australian Qualifications Framework and issued under the authority of the National Vocational Education and Training Regulator Act 2011.
• Eligibility to apply for a SafeWork NSW High-Risk Work Licence. The licence application must be submitted through Service NSW within 60 days of completing the assessment.

Maximum Number of Candidates

• Each session is limited to 8 candidates to ensure quality training and individual support

Unit of Competency

• CPCCLDG3001 Licence to Perform Dogging (DG)

Course Fee

• $1423.80
•  Full payment of course fees is required at the time of booking to secure your registration.

Payment Options

• Credit Card – via phone or online (preferred). 
• EFTPOS – available on-site.
• Invoice – available to approved corporate customers only. A 7-day credit application must be in place.
• Note: Individual candidates must use the credit card payment option.

Refund Policy

• For information on refunds, please refer to our Terms and Conditions on our website: https://www.iwpt.com.au/w/termsandconditions/

  Recognition of Prior Learning (RPL)

• Candidates wishing to apply for Recognition of Prior Learning (RPL) should contact the IWP administration team at the time of enrolment to discuss their eligibility and the application process. 

IWP Contact Details & RTO Information

• Address: 37 Kemblawarra Road, Warrawong NSW 2502
• Phone: 02 4274 3864
• Email: admin@iwpt.com.au
• Website: www.iwpt.com.au
• RTO Code: 91671
• ABN: 18 133 156 993